사견을 적어 봅니다.
페이지 정보
관련링크
본문
open arc라 하면 통상 상식적으로
1. submerged arc 와 그외 노출된 arc 용접 기법의 뜻으로 사용 될 수 있는것 같으며,
2. GMAW 와 SMAW 에서 나타나는 용적이행 현상을 나타낼 경우
SHORT-CIRCUIT TRANSFER(DIP)와 이에 반하여 FREE FRIGHT TRANSFER MODE
이에 관해서는 국제용접학회분류가 대한용접학회지에 잘 나타나 있습니다.
참조 하시면 도움이 되리라 사료 됩니다.
따라서 본 질문에 대한 답은 2에 더욱 가깝다 사료 됩니다.
아래는 인터넷에서 긁어온 것 입니다.
Metal transfer mode
The manner, or mode, in which the metal transfers from the electrode to the weld pool largely determines the operating features of the process. There are three principal metal transfer modes:
Short circuiting
Droplet / spray
Pulsed
Short-circuiting and pulsed metal transfer are used for low current operation while spray metal transfer is only used with high welding currents. In short-circuiting or'dip' transfer, the molten metal forming on the tip of the wire is transferred by the wire dipping into the weld pool. This is achieved by setting a low voltage; for a 1.2mm diameter wire, arc voltage varies from about 17V (100A) to 22V (200A). Care in setting the voltage and the inductance in relation to the wire feed speed is essential to minimise spatter. Inductance is used to control the surge in current which occurs when the wire dips into the weld pool.
For droplet or spray transfer, a much higher voltage is necessary to ensure that the wire does not make contact i.e.short-circuit, with the weld pool; for a 1.2mm diameter wire, the arc voltage varies from approximately 27V (250A) to 35V (400A). The molten metal at the tip of the wire transfers to the weld pool in the form of a spray of small droplets (about the diameter of the wire and smaller). However, there is a minimum current level, threshold, below which droplets are not forcibly projected across the arc. If an open arc technique is attempted much below the threshold current level, the low arc forces would be insufficient to prevent large droplets forming at the tip of the wire. These droplets would transfer erratically across the arc under normal gravitational forces. The pulsed mode was developed as a means of stabilising the open arc at low current levels i.e. below the threshold level, to avoid short-circuiting and spatter. Spray type metal transfer is achieved by applying pulses of current, each pulse having sufficient force to detach a droplet. Synergic pulsed MIG refers to a special type of controller which enables the power source to be tuned (pulse parameters) for the wire composition and diameter, and the pulse frequency to be set according to the wire feed speed.
Shielding gas
In addition to general shielding of the arc and the weld pool, the shielding gas performs a number of important functions:
forms the arc plasma
stabilises the arc roots on the material surface
ensures smooth transfer of molten droplets from the wire to the weld pool
Thus, the shielding gas will have a substantial effect on the stability of the arc and metal transfer and the behaviour of the weld pool, in particular, its penetration. General purpose shielding gases for MIG welding are mixtures of argon, oxygen and C02, and special gas mixtures may contain helium. The gases which are normally used for the various materials are:
steels
CO2
argon +2 to 5% oxygen
argon +5 to 25% CO2
non-ferrous
argon
argon / helium
Argon based gases, compared with CO2, are generally more tolerant to parameter settings and generate lower spatter levels with the dip transfer mode. However, there is a greater risk of lack of fusion defects because these gases are colder. As CO2 cannot be used in the open arc (pulsed or spray transfer) modes due to high back-plasma forces, argon based gases containing oxygen or CO2 are normally employed.
1. submerged arc 와 그외 노출된 arc 용접 기법의 뜻으로 사용 될 수 있는것 같으며,
2. GMAW 와 SMAW 에서 나타나는 용적이행 현상을 나타낼 경우
SHORT-CIRCUIT TRANSFER(DIP)와 이에 반하여 FREE FRIGHT TRANSFER MODE
이에 관해서는 국제용접학회분류가 대한용접학회지에 잘 나타나 있습니다.
참조 하시면 도움이 되리라 사료 됩니다.
따라서 본 질문에 대한 답은 2에 더욱 가깝다 사료 됩니다.
아래는 인터넷에서 긁어온 것 입니다.
Metal transfer mode
The manner, or mode, in which the metal transfers from the electrode to the weld pool largely determines the operating features of the process. There are three principal metal transfer modes:
Short circuiting
Droplet / spray
Pulsed
Short-circuiting and pulsed metal transfer are used for low current operation while spray metal transfer is only used with high welding currents. In short-circuiting or'dip' transfer, the molten metal forming on the tip of the wire is transferred by the wire dipping into the weld pool. This is achieved by setting a low voltage; for a 1.2mm diameter wire, arc voltage varies from about 17V (100A) to 22V (200A). Care in setting the voltage and the inductance in relation to the wire feed speed is essential to minimise spatter. Inductance is used to control the surge in current which occurs when the wire dips into the weld pool.
For droplet or spray transfer, a much higher voltage is necessary to ensure that the wire does not make contact i.e.short-circuit, with the weld pool; for a 1.2mm diameter wire, the arc voltage varies from approximately 27V (250A) to 35V (400A). The molten metal at the tip of the wire transfers to the weld pool in the form of a spray of small droplets (about the diameter of the wire and smaller). However, there is a minimum current level, threshold, below which droplets are not forcibly projected across the arc. If an open arc technique is attempted much below the threshold current level, the low arc forces would be insufficient to prevent large droplets forming at the tip of the wire. These droplets would transfer erratically across the arc under normal gravitational forces. The pulsed mode was developed as a means of stabilising the open arc at low current levels i.e. below the threshold level, to avoid short-circuiting and spatter. Spray type metal transfer is achieved by applying pulses of current, each pulse having sufficient force to detach a droplet. Synergic pulsed MIG refers to a special type of controller which enables the power source to be tuned (pulse parameters) for the wire composition and diameter, and the pulse frequency to be set according to the wire feed speed.
Shielding gas
In addition to general shielding of the arc and the weld pool, the shielding gas performs a number of important functions:
forms the arc plasma
stabilises the arc roots on the material surface
ensures smooth transfer of molten droplets from the wire to the weld pool
Thus, the shielding gas will have a substantial effect on the stability of the arc and metal transfer and the behaviour of the weld pool, in particular, its penetration. General purpose shielding gases for MIG welding are mixtures of argon, oxygen and C02, and special gas mixtures may contain helium. The gases which are normally used for the various materials are:
steels
CO2
argon +2 to 5% oxygen
argon +5 to 25% CO2
non-ferrous
argon
argon / helium
Argon based gases, compared with CO2, are generally more tolerant to parameter settings and generate lower spatter levels with the dip transfer mode. However, there is a greater risk of lack of fusion defects because these gases are colder. As CO2 cannot be used in the open arc (pulsed or spray transfer) modes due to high back-plasma forces, argon based gases containing oxygen or CO2 are normally employed.
댓글목록